Tag Archives: ILL-BC7

PCR – Oly RAD-seq Prep Scale PCR

Continuing with the RAD-seq library prep. Following the Meyer Lab 2bRAD protocol.
After determining the minimum number of PCR cycles to run to generate a visible, 166bp band on a gel yesterday, ran a full library “prep scale” PCR.

 

REAGENT SINGLE REACTION (μL) x11
Template 40 NA
ILL-HT1 (1μM) 5 55
ILL-BC# (1μM) 5 NA
NanoPure H2O 5 55
dNTPs (1mM) 20 220
ILL-LIB1 (10μM) 2 22
ILL-LIB2 (10μM) 2 22
5x Q5 Reaction Buffer 20 220
Q5 DNA Polymerase 1 11
TOTAL 100 550

 

Combined the following for PCR reactions:

  • 55μL PCR master mix
  • 40μL ligation mix
  • 5μL of ILL-BC# (1μM) – The barcode number and the respective sample are listed below.

 

SAMPLE BARCODE SEQUENCE
Oly RAD 02  1  CGTGAT
Oly RAD 03  2  ACATCG
Oly RAD 04  3  GCCTAA
Oly RAD 06  4  TGGTCA
Oly RAD 07  5  CACTGT
Oly RAD 08  6  ATTGGC
Oly RAD 14  7  GATCTG
Oly RAD 17  8  TCAAGT
Oly RAD 23  9  CTGATC
Oly RAD 30 10 AAGCTA

 

Cycling was performed on a PTC-200 (MJ Research) with a heated lid:

STEP TEMP (C) TIME (s)
Initial Denaturation
  • 98
  • 30
17 cycles
  • 98
  • 60
  • 72
  • 5
  • 20
  • 10

 

After cycling, added 16μL of 6x loading dye to each sample.

Loaded 10μL of ladder on each of the two gels.

Results:

 

Things looked fine. Excised the bands from each sample indicated by the green arrow. Before and after gel images show regions excised. Will purify the bands and quantify library yields.

Share

PCR – Oly RAD-seq Prep Scale PCR

Continuing with the RAD-seq library prep. Following the Meyer Lab 2bRAD protocol.

After determining the minimum number of PCR cycles to run to generate a visible, 166bp band on a gel yesterday, ran a full library “prep scale” PCR.

 

REAGENT SINGLE REACTION (μL) x11
Template 40 NA
ILL-HT1 (1μM) 5 NA
ILL-BC# (1μM) 5 NA
NanoPure H2O 5 55
dNTPs (10mM) 20 220
ILL-LIB1 (10μM) 2 22
ILL-LIB2 (10μM) 2 22
5x Q5 Reaction Buffer 20 220
Q5 DNA Polymerase 1 11
TOTAL 100 550

 

Combined the following for PCR reactions:

  • 50μL PCR master mix
  • 40μL ligation mix
  • 5μL of ILL-HT1 (1μM)
  • 5μL of ILL-BC# (1μM) – The barcode number and the respective sample are listed below.

NOTE: Samples 02, 03, & 04 did not have 40μL of the ligation reaction left (only 32μL) due to additional usage in the test scale PCR yesterday. Supplemented those three reactions with 8μL of H2O to bring them to 100μL.

 

SAMPLE BARCODE SEQUENCE
Oly RAD 02  1  CGTGAT
Oly RAD 03  2  ACATCG
Oly RAD 04  3  GCCTAA
Oly RAD 06  4  TGGTCA
Oly RAD 07  5  CACTGT
Oly RAD 08  6  ATTGGC
Oly RAD 14  7  GATCTG
Oly RAD 17  8  TCAAGT
Oly RAD 23  9  CTGATC
Oly RAD 30 10 AAGCTA

 

Cycling was performed on a PTC-200 (MJ Research) with a heated lid:

STEP TEMP (C) TIME (s)
Initial Denaturation
  • 98
  • 30
12 cycles
  • 98
  • 60
  • 72
  • 5
  • 20
  • 10

 

After cycling, added 16μL of 6x loading dye to each sample.

Due to limitations in available comb sizes and inability to combine combs to make larger well sizes, only loaded 58μL of samples in each well on this gel. Will load remainder on a second gel and combine after PCR products are purified.

Results:

 

Well, this is lame. There are absolutely no PCR products on this gel. In fact, this just looks like big smears of degraded DNA. I was expecting an amplicon of ~166bp to cut out of the gel. Based off of the test scale PCR from yesterday, everything should have been hunky dory. Not really sure what to think about this…

Share